Multi Zone Disabled Toilet Alarm System

Home

Trade Customers

Multi Zone

Multi-Zone disabled toilet indicator (6 zones) Ref: AA3111OD

The Multi-Zone disabled toilet alarm system is designed for larger premises which require central indication of alarm calls from toilets. The system caters for up to 6 toilets and is designed to give dual re-assurance at the point of operation. If you require a system for more than 6 toilets, simply stack systems together or call us for further options.
When a pull cord (S1600) is operated its LED flashes and a local buzzer (S1778) sounds to inform the caller that the call has been transmitted. When the call is silenced at the panel the flashing LED becomes steady and the local buzzer silences to inform the caller that the call has been received and help is on the way. If the caller pulls the cord again the LED on the pull cord will flash and the local buzzer sounds again. When help does arrive and the call is reset then all LED's and buzzers, flashing or steady are extinguished. An integral PSU and battery are included.

In addition to the A31110D control panel you will require the following for each toilet:

1 x pull cord (S1600)

1 x over door light / sounder (S1778PR or S1778SR)

1 x reset button (S1708PR or S1708S)

This system is fully compliant with BS8300 and the requirements of the Disability Discrimination Act.

Product Information Sheet

Installation Instructions

Price: £267.95 (Excluding VAT at 17.5%)

Quantity:

Ceiling Pull Cord Ref: S1600

Non-latching ceiling pull cord with re-assurance LED for use directly with AIDLARMs above.
This unit has voltage free SPCO contacts. The LED incorporates a current limit resistor for use on 12vdc.
Has an anti - ligature facility, with a breaking weight of 46 pounds and is 2.5metres long. However, it is considered against best practise to install a pull cord into a mental health unit due to the risk it poses. Call buttons in the toilet or Panic strip is recommended.

Price: £12.65 (Excluding VAT at 17.5%)

Quantity:

Press to Reset button Stainless steel Ref: S1708S

Stainless steel engraved vandal resistant reset button. This is a non-latching unit with change over contacts.
These items are supplied with a galvanised steel mounting box to enable them to be flush fitted to the wall. They can be surface mounted using part no. S0610 listed below.

Product Information Sheet

Installation Instructions

Price: £39.79 (Excluding VAT at 17.5%)

Quantity:

Red Overdoor Light and sounder Stainless steel Ref: S1778SR

Stainless steel Overdoor Light/Sounder unit. There are separate drive inputs for both the light and the sounder. These items are supplied with a galvanised steel mounting box to enable them to be flush fitted to the wall. They can be surface mounted using part no. S0610 listed below.

Product Information Sheet

Installation Instructions

Price: £44.66 (Excluding VAT at 17.5%)

Quantity:

Reset Button with reassurance LEDs and Buzzer Ref: S1708P

A wall mounted RESET button in white ABS complete with a single gang mounting box This is a non-latching unit with a N.O. contacts. The LEDs (Available in RED, BLUE, GREEN or YELLOW) and buzzer have separate terminals for acknowledge purposes. The LED current limit resistor is provided for 12 vdc operation. The button contacts are rated at 50ma 24vdc resistive, N.O. press to close They should NOT be used for switch feeds to door strikes or mag locks etc.

Surface mount only 36mm deep

Back box supplied for surface mount

Flush mount 18mm onto standard galvanised box (Not supplied)

Mark resistant decal

Tactile button

Two high brightness LEDs

Integral buzzer

Product Information Sheet

Installation Instructions

Price: £18.25 (Excluding VAT at 17.5%)

Select LED Colour

Quantity:

Overdoor light and buzzer with LEDs Ref: S1778P

Overdoor light with 8 high brightness LEDs (RED, BLUE, GREEN or YELLOW) and an integral buzzer. The LEDs are current limited for 12vdc operation. The single gang low profile ABS enclosure is fitted with a mark resistant decal. For a high power siunder version see our S1788P range.

Surface mount only 36mm deep

Back box supplied for surface mount

Flush mount 18mm onto standard galvanised box (Not supplied)

Mark resistant decal

Product Information Sheet

Installation Instructions

Price: £24.95 (Excluding VAT at 17.5%)

Select LED Colour

Quantity:

Safety Products | Disabled Toilet Alarms | Multi Zone